Common Electrical Faults In Your Home

Light switches don’t work

If you move into a new property and a switch doesn’t do anything at all, it may have been disconnected. Alternatively, it could be down to a problem with the outlet, circuit or wiring. This will need the attention of an electrician. Dimmer switches that don’t work properly may be victims of poor workmanship or simply substandard.

Lights are too bright or too dim

There are two likely explanations. You may be inadvertently using different types of lights, with different wattages. Check to make sure they all match. Alternatively, it may be down to a bad main neutral connection. This latter problem needs the attention of a professional.

Repeated electrical surges

These can be caused by damaged power lines, faulty appliances, bad wiring or even lightning strikes. The surge may be short-lived but repeated surges can damage electrical components. Recurring surges are most likely down to an electrical device in your home, or the domestic wiring. If disconnecting cheap appliances or power boards doesn’t end the problem, it’s time to call in an electrician.

Dips in power

These can also be caused by faulty or substandard devices. This time, using too much power when activated.

The circuit breaker keeps tripping

Circuit breakers can be tripped by high-demand items such as hair-dryers and microwaves, especially if other items are used on the same source. Take note of what appliances you had on when the circuit tripped. In future, try putting them on a lower setting. Alternatively, don’t connect multiple high-power devices to one circuit.

Electrical shocks

Thankfully, most electric shocks are relatively mild but, even then, they are a warning sign. They mostly happen when a device is being switched on or off and may be down to either the appliance or the wiring. If you receive any kind of electric shock, no matter how mild, you should definitely call in an expert.

Light bulbs burning out repeatedly

There are various possible causes for this. Your wattage may be too high. Insulation may be too near to the light. There may be bad wiring in the circuit or mains. A dimmer switch may have too much wattage on one switch. Flickering could suggest a poor connection. Again, this may require the attention of an electrician.

Recessed lights turn off then come back on again

Recessed lighting is designed to cut out when it gets too hot. This is likely to be caused by either too much wattage on the bulb or the insulation in the ceiling being too near the bulb. If cut-outs do happen, check for excessive heat, as this can be a fire hazard.

What Are The Benefits of Outdoor Lighting

As the days grow longer and the nights get warmer, more people will be spending time outside. But no one wants to be outside in the dark. So why should you have exterior lighting for your home?

The main reason to have exterior lighting is to extend your living space. Are you someone who likes to entertain? Whether you have a simple patio or a backyard, adding exterior lighting will allow you to use those spaces more and for a longer period of time. That way you will be able to extend your backyard barbecues and have more outside social events.

Another reason to add exterior lighting to your outside space is for safety and security. Adding exterior lighting to your home helps to deter burglars and vandals, keeping your house, its members and your valuables safe. You can also use exterior lighting to illuminate walkways or other paths around your house, allowing you to use those things safely.

Exterior lighting is also a great way to add curb appeal to your home. Adding exterior lighting will enhance your home’s appearance and make it stand out from surrounding houses. You can also use exterior lighting to highlight certain architectural features, adding prominence to a sculpture or water feature.

Just like interior lighting, exterior lighting has changed over the years. With the advent of LED technology, exterior lighting has become more cost effective and worthwhile. Regardless of your reason, adding exterior lighting to your living space is a great thing to do, especially during the spring and summer months.

5 Factors To Consider When Hiring Electric Company

Electrical services on commercial sector should only be offered by professional electricians. Wiring and other installations are not services that can just be undertaken by inexperienced individual or company hoping that installation will turn out just okay. Planning and the implementation of the whole project require the expertise of electrical contractors that have been doing these types of jobs for several years. In this article, we will explore the main factors that you should consider when choosing an electric company.

Below are the 6 critical factors that you should consider before choosing an electric company.

1. Experience and expertise. It is critical you check for how long the company has been operating. The best electric company commercial need to have several years of experience and proven expertise.

2. Ask for their license and ask them about their insurance documents. This is a critical factor that you need to consider it shows the firm is recognized and insured thus in case there were damages they would be covered by insurance company.

3. Inquire regarding the training and seminars that the electricians have undergone. It is imperative that the employees of the firms have the right technical skills to offer professional services. Electric company commercial need to have experts who have proven track record.

Certain contractors will get laborers from other companies if they lack workers. It is best to ask them for the license of all of the electricians and their line of expertise.

4. The companies reputation

The reputation of the company will help you in making the right decision, the company offering the best services will have a good reputation and this will give you a good indication of the service quality.

5. The company’s safety and precaution policy

The most vital thing when considering contractors is checking their safety program. Check if they have excellent safety programs for their clients and even with their electricians. A reliable and professional electrical service company would never allow their personnel to work without any safety gear.

6. The fee charged

Before reaching the final decision of hiring commercial electric company, it would be best to get a quotation and do bidding, especially for large-scale projects. Provide the scope of work that needs to be done, interview the contractors separately and then use the information to draft the final scope of the work. Make sure that at least 3 electrical companies will bid on the project for better results and for possible discounts.

7. Timeframe

Many electrical projects are time sensitive. You can’t wait for days on end for someone to bring power back to your house, in case of a fuse is blown up. It’s an emergency which needs to be addressed as quickly as possible. So you need to find an electrical contractor who would make your job a priority and give it all its due attention.

Other than the above, some of your electrical projects might be long-term ones such as when you are renovating your house or revamping the whole property. It is really important that the electrical contractors that you work with are reliable and honest. People who give correct project estimates and stick to it. People who give importance to project and don’t cut it short when they get other work or don’t keep elongating your project because they have no work.

Electrician - SMD Electrical Contractors

Common Fusebox Problems To Look Out For

A fuse box (sometimes referred to as a breaker panel) represents the electrical “central nervous system” of your home. While these are highly reliable pieces of equipment, there can still be times when problems will occur. These must be addressed by a trained professional for safety reasons. It is nonetheless a good idea to take a look at some common signals that expert help is required. Let’s examine a handful of symptoms that should be diagnosed by a licensed electrician.

Fuses that Frequently Trip for no Apparent Reason

Fuses are meant to protect a home and all associated equipment from electrical overloads. There can be times when a fuse trips or “blows” frequently and subsequently needs to be reset. This is often a symptom of bad wiring or a short circuit contained within the box. An electrician will be able to discover the exact root of this problem.

Fuses that are Loose or Fall Out

Fuses are meant to sit within their terminals snugly. However, there are times when one or more becomes loose. This might signal that the terminals have become corroded or otherwise mechanically impaired. Once again, always seek the advice of an expert as opposed to trying to sort the problem out yourself.

Melted Fuses and/or Burnt Terminals

This is a definite signal that something is awry. Burnt fuses or melted terminals are the result of overheating; a sign that there is a serious problem with the fuse box. If you happen to notice this symptom, call Pulse Electrix as soon as possible. Our electricians in Manchester are more than happy to be of assistance.

Strange Smells or Sounds Emitting from the Fuse Box

Have you recently noticed strange hissing or popping noises coming from the fuse box? Does it emit a strong or acrid odour? These are concrete signs that there is a serious internal issue. Once again, do not wait to speak with a professional. Such problems will not disappear on their own and in severe cases, a fire could occur.

A fuse box is one of the most important electrical components within your home, so it only makes sense that regular maintenance and safety checks are critical. Please do not hesitate to use this article as a quick checklist if you suspect that an issue may be present. Finally, always employ the services of a fully licensed and insured electrician.

RCD fuseboard installation

Should I Call a Domestic Electrician for a Tripping Fuse Box?

9 times out of 10, a tripping fuse board is doing its job correctly – protecting you from potentially dangerous electrical faults in your home. Our fully insured expert electricians can inspect your electrics and advise you on what’s causing the fuse board to trip, whether it’s inadequate wiring or a faulty appliance.

What to do when RCDs trips?

First thing to do reset it by turning RCD back on, you may find it trips straight back off again. In this case turn all MCBs (fuses) off, then try to reset RCD by turning it on. If the RCD stays on then one by one turn MCBs on. If there is a fault on one of the circuits, RCD will trips out by one of the MCBs (fuses). In that case leave faulty fuse off then contact an Electrician.

If RCD won’t switch on even when all MCBs (fuses) are off, then go around the house and unplug all plugs from sockets and turn off all switches (light and …)
Don’t worry about things you can’t get to them or no access to unplug.
Then go back to RCD and turn it on, if it stays on then turn MCBs (fuses) on one by one then go back and plug in, all plugs one by one till one of them trips RCD off. Then you know what is the fault. If you find fault is in lighting circuit by turning light switch on and that trips RCD of then contact electrician.

Faulty Electrical Appliance

Do you find that the problem is triggered every time you plug in or switch on a particular appliance? If so, this is the likely cause. Replacing a kettle or iron may be the solution.

If you are unsure about the cause, head back to the fuse box and see which other switches are off. Go to the room affected and switch off all electrical items at the socket. Put the fuse box switches back to the on position. Now work around the room, switching on the items that you wish to use. Do any cut the electricity supply?

Overloaded Plug Sockets

Can you see that one plug socket is powering too many items? An extension lead charging multiple active devices from one socket could cause a surge of electricity. Spreading the load could resolve the issue.

If you are short on plug sockets, a domestic electrician can install additional ones at convenient points around your home.

Faulty Wiring

If you have a reoccurring issue and the main circuit breaker is the only switch that goes off, it usually suggests an earth fault in the fuse box wiring. This is the point when you need to call out a domestic electrician.

Ask your local electrician to undertake an Electrical Installation Condition Report (EICR). This will cover a test of the circuits to diagnose the issue. They will check that the fuse box is safe to use, look at the general wear and tear and ensure that your circuits meet the IET wiring regulations. Minor issues can usually be resolved during that visit and they will provide you with a copy of the report.

If it no longer complies with current standards, your domestic electrician will need to replace the fuse box. This is non-negotiable, as the priority is your safety.

Call on your local Domestic Electrician in Staffordshire

Does your property have fire protection? GET PROTECTED!!!! Contact 01782 216911 for information or for a quotation.

RCD fuseboard installation

Why You Need An RCD Fitted In Your Home

Your electrical installation should be checked every 10 years by a qualified electrician, but an RCD is a key safety device that every household should install within your fuseboard.
We all use electricity in our homes every day without thinking about how safe it is. But the campaigning charity Electrical Safety First estimates that around 70 people are killed, with 350,000 seriously injured annually due to an electrical accident in the home.

An RCD is a safety device that helps protect against electric shock or fire by interrupting the flow of electricity when it detects a fault. RCDs are very sensitive and should be installed on your fuseboard to provide the greatest protection. You can also find RCD switches on sockets, as well as on portable devices that can be plugged into standard sockets.

Fitting RCDs into fuseboards across all circuits has been part of the UK safety standard since 2008. Current regulations say all socket outlets should be covered by a 30amp RCD. If you’ve got any installations outside or in the bathroom, an RCD is essential. If you don’t have one on the circuit when you’re using a lawnmower or other electrical products outside, ensure there’s an RCD on the flex cable to protect you if the cable is accidentally cut.

If your home wiring was installed before 2008, or has not been checked recently, it’s worth getting SMD Electrical and our team of qualified electricians in to ensure you have the necessary RCDs on your fuseboard.

RCD’s are so essential, especially when anyone is conducting any electrical work in your home. For any information on our RCD installations contact SMD Electrical on 01782 216911.

When fitted, an RCD (residual current device) will monitor your wiring throughout your home and will instantly break an electric circuit if they detect an unbalanced/leaking current, therefore protecting you from any risks of electrocution or fires. Essentially they will switch the electricity off automatically if they detect a fault.
The amount of current that can leak through is more than enough to cause significant harm to anybody who comes into contact with it, including cardiac arrest. RCD’s can detect these leakages and disconnect the current in as little as 40 milliseconds to reduce the severity of any injuries.
The catch? There are none! There is literally no excuse not to have this lifesaving device installed in your home. RCD’s are so essential, especially when anyone is conducting any electrical work in your home.
There are three main types of RCD’s; fixed RCD’s, Socket-Outlet RCD’s and Portable RCD’s. Each have their own unique uses and benefits, for more information take a look at our RCD guide.
If you know you need to get an RCD fitted in your home or if you want further reassurance over your electrical safety, use our Find An Electrician tool to find a registered electrician in your area.

3 Ways To Improve your Companies Access Control System

Building access control systems – or home control systems – are developed to ensure the safety of people and data within the premises. An essential feature of an access control system is to ensure that only authorised individuals are allowed entry to specific areas of an infrastructural facility. Efficiently installing an access control system can enable an organisation to control who is accessing their facilities, ensuring safety for all. An access control point is integrated into either a door, turnstile, parking gate, elevator, or other physical barriers, where access points can be electronically controlled – typically, these points happen to be a door. It is crucial for entities (residential or commercial) to keep their occupants and assets safe by having an effective system in place. These security measures can be kept up-to-date by considering the listed points.

Evaluate the usefulness of your system

First and foremost, one should inspect what the fundamental purpose of their system is and whether the current system is effectively providing that. A significant factor to consider is the location of your control systems and whether it protects the individuals and assets which genuinely require it.

Review who has access

Some systems are faced with an issue where the number of active cards controlling the system exceeds the number of employees or residents actually requiring it. Such errors can be expected across organisations, although this can be avoided by setting features to timeout the cards. These situations can be as follows:

  • If the card is not used for a predetermined amount of time at the control facility, access is shut off.
  • After a certain period of inactivity, cards must be renewed.
  • Connect the card to human resources databases.

Upgrade your technology

It is suggested that a 125-kilohertz technology system is now outdated & should be updated. Building security managers should start installing encrypted technology instead. Ideally, an access control system should be updated every ten years and not treated as a one-time investment.

Regular testing

A Building management system functionality should be tested on a monthly or quarterly this will ensure proper functionality and allows security managers to plan any possible changes required well in advance.

Watch out for tailgating

Politely holding open the door when requested is a common practice but can lead to potential risks. Employees should be educated to observe strictly who they are opening the door for. A frequent assumption is that bypassing an established security system is challenging, leading to complacency and casualness – which is why multiple layers of security should be enforced to deal with the problem of tailgating.

The safety of individuals on the premises is equally vital to concealing valuable data. Access control systems are crucial to prevent the theft of knowledge or critical components, as well as nullifying threats to the safety of employees or residents. This further validates the need to periodically assess the efficiency of your access control system in place.




SMD Electrical are recruiting for security engineers. Are you a security engineer looking to work with a local, honest and respectable company? If so pop in for a coffee or call Luke on 01782 216911.

As a Security Engineer you will  be responsible for the installation and service of CCTV, Intruder Alarms, Fire Alarm Systems and Access Control.

You will be provided with:
– Company Vehicle
– Company Uniform
– Full initial and on-going Product Training

You should be:
– Self-motivated
– Be of smart appearance
– Previous experience working within a similar role
– Must have background working with Intruder Alarms, CCTV and Access Control systems
– Full valid UK Driving Licence
– Flexible regarding working hours

Excellent communication skills – both verbal and written.

This is a full time position based from home with the expectancy to travel to our office as and when required.

If you are interested and feel you have the relevant skills and experience, please email a copy of your CV to:


SMD Secure Fire Alarm Project At Local School

SMD Electrical have been awarded the contract to supply, install & commission an addressable Protec fire alarm system at a local primary school. A huge thanks to Protec Fire for the supply of the materials and their assistance with the project. All prestart meetings are complete and our engineers are on site and the project is going well.


Does your property have fire protection? GET PROTECTED!!!! Contact 01782 216911 for information or for a quotation.


We are delighted to announce that we have secured the contract and are on site to carry out a IP CCTV installation at a very well known bakery. The system will consist of 40 plus IP cameras from PTZ’s, to turret’s & bullets. We have worked with the bakeries security team and our suppliers to design an IP based system to suit their needs. More information will be published as the job progresses…

For any information on IP CCTV systems contact 01782 216911.